HOW TO setup a Starx Masternode :D:D guide and videoguide whith Vultr.com vps service

hi all

You can find this guide on ghithub but it is not up to date
https://github.com/ezehy/starcashx/blob/master/masternodeguide.txt

This guide is for a single masternode,
on a Ubuntu 16.04 64bit server (VPS) running headless and will
be controlled from the wallet on your local computer (Control wallet).
The wallet on the the VPS will be referred to as the Remote wallet.

You will need your server details for progressing through this guide.

First the basic requirements:

1. Starx MN Collateral (3000 starx)

2. A main computer (Your everyday computer) – This will run
   the control wallet, hold your MN Collateral and can be turned on
   and off without affecting the masternode.

3. Masternode Server (VPS – The computer that will be on 24/7)

4. A unique IP address for your VPS / Remote wallet

(For security reasons, you’re are going to need a different IP
for each masternode you plan to host)

The basic reasoning for these requirements is that, you get to
keep your Starx in your local wallet and host your masternode
remotely, securely.

step1. Local Wallet Configuration

1. Using the control wallet, enter the debug console
   (Tools >help - Debug console) and type the following
   command: masternode genkey (This will be the masternode’s privkey.
   We’ll use this later…)

9UxVoYQECJkQxZqk8z5w4hNfcnrhVuGkJgYdNGGze2icmRikU31

1. Using the control wallet still, enter the following
   command: getaccountaddress ChooseAnyNameForYourNewAddress

SZPQ44txnPusXPRAvHSaw9TdffggRLUYxy

1. Still in the control wallet, send MN Collateral to
   the address you generated in step 2 (Be 100% sure that
   you entered the address correctly. You can verify this
   when you paste the address into the “Pay To:” field, the
   label will autopopulate with the name you chose”, also make
   sure this is exactly MN Collateral. No less, no more.) – Be absolutely
   100% sure that this is copied correctly. And then check it again. We
   cannot help you, if you send MN Collateral to an incorrect address.

1. Still in the control wallet, enter the command into the
   console: masternode outputs (This gets the proof of transaction
   of sending MN Collateral)
   "da8cfb9e38d25dae49bc99cde0dd2a3921e317f60d73c945f1884c48ae52ce98" : "0"

1. go to masternode tab and fill in the needed details:
   alias (this is the name of address you choose in step 2)
   MN01
   address (vps iP)
   199.247.13.227:22
   txhash (result from step 4)
   da8cfb9e38d25dae49bc99cde0dd2a3921e317f60d73c945f1884c48ae52ce98
   ouput index (this is the second result generated in step 4, its
   mostly 0 or 1)
   0

privkey: Result generated from step 1

9UxVoYQECJkQxZqk8z5w4hNfcnrhVuGkJgYdNGGze2icmRikU31

address reward
SW7BhgutQDeugLPV7DQWbhfQUJp3UDvpPs

VPS Remote wallet install

1. Log in to your VPS console as root or sudo user and copy paste lines:

cd ~ && sudo apt-get update && sudo apt-get install unzip nano libboost-system-dev libboost-filesystem-dev libboost-program-options-dev libboost-thread-dev software-properties-common -y

sudo add-apt-repository ppa:bitcoin/bitcoin -y

sudo apt-get install libboost-all-dev

sudo apt-get update && sudo apt-get install libdb5.3-dev libdb5.3++-dev libminiupnpc-dev libevent-2.0-5 libevent-pthreads-2.0-5 libevent-dev -y && wget https://github.com/ezehy/starcashx/raw/master/starsxubunew.zip && unzip starsxubunew.zip

./StarCashXd

Configuration Cont.

Now on the VPS, edit the eBux configuration file:

nano ~/.StarCashX/StarCashX.conf

Make the config look like this:

rpcuser=bullau1stmasternodestarx

rpcpassword=bullau1stmasternodestarxpassword

rpcallowip=127.0.0.1

server=1

daemon=1

logtimestamps=1

maxconnections=256

masternode=1

masternodeprivkey=9UxVoYQECJkQxZqk8z5w4hNfcnrhVuGkJgYdNGGze2icmRikU31

Make sure to replace rpcuser and rpcpassword with your own.

to exit the editor press Ctrl+o, enter and Ctrl+x

Start your masternode

Now, you need to finally start these things in this order –
Start the daemon client in the VPS. First go back to your
installed wallet directory,

cd ~

and then start the wallet using

./StarCashXd

Now, restart Control wallet, go to Masternode tab, select masternode and press "Start"

The following should appear: “Alias: “ “Successfully started masternode”,

Congratulations! You have successfully created your masternode!