| Welcome Everybody and Everyone take my Salam |
|---|
Hello,I am @rafi67
From Bangladesh
Hello my Steamian Friends,
How are you all.I hope everybody are doing very well. Today I am engaged by @mahadisalim Sir. "Creating an Electrical Series Board." I want to participate in the engagement. I hope you all like it. First of all I would like to thank @mahadisalim Sir for organizing such a beautiful engagement. Let's start without further ado.
)
Thumbnail photo and designed by Canva
| Question :-01 is- Make a series board and share the technique of making it in at least five steps with drawings.[Note: Practical work is to be shared with your photos.] |
|---|
Answer :-
Below I am showing you how to make a series circuit board step by step:-
I usually draw a drawing or diagram before any electrical work. Then I start the practical work. So I first drew a diagram for how to make a series circuit board:-
After drawing the series circuit, now I will start my practical work:-
What is needed to make a series circuit board:-
| And cable 0.5 R.M:-(1-1.5) meter |
|---|
First I connected the cable from the input of the push button of the multi socket to the output. Then I took the cable from the output of the push button and connected the cable to one end of the two pin socket and connected another cable to the other end of the two pin socket. I did this in the first step.
Now let's come to the second step. Here I took a cable from one end of the cable that I connected to the two pin of the multi socket and connected it to the lamp holder and left the other end for the 220 volt power supply.
In the third step, I made a neutral connection to the lamp holder.
In this step, I made a cable connection to a two-pin plug.
In the fifth step, I completed my work. In this step, I connected a 200 watt lamp to the holder. Then I connected one end of the cable that I connected to the two-pin of the multi-socket to the lamp holder and gave a 220 volt phase connection to the other end. I made a neutral connection to the black cable of the holder.
Finally, I switched on and checked and completed my work without any accident.
You can make this series circuit board very easily at home or in the office. This is possible at very low cost. And you can find out the problem of any electric or electronic device of the home or office through this series circuit board.
| Question :-02 is-Check with two electrical or electronic device series boards and show results. |
|---|
Answer :-
After making my series circuit board, I checked two electrical devices with this board. Respectively:-
| 01/Two Pole MCB or Circuit Breaker |
|---|
Circuit Breaker Checking :-
So I will first discuss how I checked a circuit breaker with a series circuit board:-First I turned on the circuit breaker and held the series line cable at one end. But no lamp lights up on the series board. Then I held it at the other end of the circuit breaker. Here the lamp of the series circuit board is lit. So by this checking we can understand that one pole is bad among the two poles of this circuit breaker. So it is a bad circuit breaker.
Push Button Checking :-
I took a push button and will check its N.C auxiliary end. N.C means normally closed so if the series circuit board line is in good condition here the lamp will light up. Let's see what happens. I took the series circuit board line and the lamp of the series circuit board is on. Then we can say that this is a good push button.
With this series circuit board we can check many types of electric and electronics devices. Such as:-Motor, Transformer, Limit Switch, Push Button, Capacitor and any type of short circuit.
| Question :-03 is-Check with a short piece of cable in a series board and show the result. |
|---|
Answer :-
How to check a short piece cable, I will show you below:-
First I took a 1 foot cable. Then I held the cable of the series circuit board at both ends of this cable. Since the series light is on when I hold it at both ends, so it is a good cable. In this method we can check any cable. Whether the cable is bad or good or whether there is any short in the cable, all the problems can be found out through this series circuit board.
| Thank you everyone for reading my post |
|---|
| I invited 03 steemian friends |
|---|
