Greetings Brothers and Sisters,
Opensource Technology: 3D Printer, Neodymium magnets n52 12mm x 3mm, 32AWG Magnet wire, Bedini SSG Circuit, HDD harddrive bearings and shaft. 12V Batteries
https://mega.nz/#F!0MckWLgK!MAx2pIm7axMxfXdjGYXblA
Much Love and thanks to Vortex Magnetics for the opensource release of their brushless motor/generator .STL files
http://1nce.host/u/vortmath/public/Bobbin%20A.stl/
http://1nce.host/u/vortmath/public/Bobbin%20B.stl/
http://1nce.host/u/vortmath/public/Peg.stl/
http://1nce.host/u/vortmath/public/Rotor.stl/
http://1nce.host/u/vortmath/public/Stator.stl/
https://mega.nz/#F!0MckWLgK!MAx2pIm7axMxfXdjGYXblA
Stator files designed to house a stander HDD Hard Drive Bearings and Shaft:
Rotor files designed to house Neodymium magnets n52 12mm x 3mm
)
Bobbin files form the bifiliar coils - two strands of 32AWG magnet wire @ 144 turns:
Standard Bedini SSG Circuit should run it just fine, consider potentiometer
Ebook on Bedini SG Motor http://anyflip.com/tkbd/csnc
Can a half dead 12v battery charge multiple 12v deep cycle batteries?
Very interesting, I bet we can get this printed out and created here at the shop. What's the use of the device and do you have any video of it working?
Downvoting a post can decrease pending rewards and make it less visible. Common reasons:
Submit
https://steemit.com/diy/@opsacredfire/vortex-magnetic-s-motor-generator-coil-fix-stl-3d-printer-files-opensource-prototyping
Downvoting a post can decrease pending rewards and make it less visible. Common reasons:
Submit
This is an opensource prototyping project we will all be building together. The basic bedini circuit will only require One bobbin print turned into a 32awglar coil @ 144 turns. This should operate the circuit just fine. With that circuit operational. This should easily show one battery running a motor charging another battery. With a little innerstanding of Tesla impulse technology you can feel how the battery runs the circuit that fires the motor to spin. Each time the electromagnet fires there is an impulse created through the coils and wire. By placing multiple coils (long lengths of wire wrapped small) in line with that pulse you can use a Full wave bridge rectifier to capture a postive and negative lead off that wire. It may not read on multimeter but if you run that post and neg legs of the rectifier to a battery or an ac start run capacitor you will see it fill. Be careful ac start run caps dump real hard. Pretty wild to see a little 12v pulse run motor and fire caps
Downvoting a post can decrease pending rewards and make it less visible. Common reasons:
Submit
https://steemit.com/diy/@opsacredfire/the-daftman-circuit-for-use-with-vortex-magnetic-s-motor-generator-stl-3d-printer-files-opensource-prototyping
Downvoting a post can decrease pending rewards and make it less visible. Common reasons:
Submit
Thanks for the files! I was waiting for you to put these out. I would like to see if I can get it done. Looks like I might already have other minds to take a look .
Downvoting a post can decrease pending rewards and make it less visible. Common reasons:
Submit
Happy to share, thanks to Vortex Magnetic's for all the time crunching out the stls
Downvoting a post can decrease pending rewards and make it less visible. Common reasons:
Submit
https://steemit.com/diy/@opsacredfire/the-daftman-circuit-for-use-with-vortex-magnetic-s-motor-generator-stl-3d-printer-files-opensource-prototyping
Downvoting a post can decrease pending rewards and make it less visible. Common reasons:
Submit
https://steemit.com/diy/@opsacredfire/vortex-magnetic-s-motor-generator-coil-fix-stl-3d-printer-files-opensource-prototyping
Downvoting a post can decrease pending rewards and make it less visible. Common reasons:
Submit
Newst version
Downvoting a post can decrease pending rewards and make it less visible. Common reasons:
Submit