Ford Fairlane 500 Skyliner motor and spark plug wire detailingsteemCreated with Sketch.

in makerwannabe •  8 years ago 

I moved on to seeing how the engine would fit, so cut the pieces free from the sprue and loosely assembled it. I tape the body together again, as it kept falling apart.

I was checking to see if I could lift the air clear a touch as it sits almost on top of the distributor. There does seem to be room to do this. Not 100% sure though, so instead I am going to try some thing else I think.

Above is the view from the side showing a gap. Further inspection showed this was down to the front suspension not being seated correctly.

Here is a look from the bottom, the wheel shaft should be quite a bit higher, it looks as though the bottom suspension is not even touching the chassis.

Above I am holding the front suspension in it’s correct place. The gap between wher the hood would be and the air cleaner is now much smaller.

On to getting ready for spark plug wires…

Being a firm believer in using what’s at hand (some would say, a cheapskate) I found some wires that may do the trick.

Close up picture shows how the air cleaner really does touch the distributor.

Looks messy but the air cleaner covers it mostly. I don’t have the tiny drill bits that I see many model builders using, so I came up with a plan, more on that below.

Air cleaner on and it does not look that bad. Here you can see the first wire goes from the coil, to the centre of the distributor. The second wired comes out of the distributor, over the valve cover to the spark plug.

Same as photo above, only now without the air cleaner.

My cheapskate wires!

Here is where you usually find them, tied around cables too keep them in check.

Test fitting and seeing how it all looks inside the engine bay. Looks like it will work to me.

The method I use is a bit messy, basically I heat up the wire, then push it into the distributor while it is very hot and melt a hole. I have made nine holes in here. With all the wires in, I don’t think it will look too bad, but time will tell.

With the air cleaner on the wire is almost not noticeable, and the messy distributor even less so.

Test fitting a wheel, I really like the look of these wheels!

The cylinder heads have pointy bits on them. Initially I thought they were meant to be the spark plugs, so I butchered two to take the wires.

Figured out that they actually represent the exhaust headers going onto the cylinder heads. The photo above shows that I added four holes, roughly where the spark plugs actually would be.

Another shot showing the holes where the spark plug wires will go into.

Underneath, you can see the wire poking through. This is ok as there is s gap, between this part and the engine block.

Almost time to slap some paint on the motor!

Follow me!

Another repost from my blog, over at http://makerwannabe.com/
Once I have put it all on the blockchain i hope to use the blockchain as my database for the posts!

Authors get paid when people like you upvote their post.
If you enjoyed what you read here, create your account today and start earning FREE STEEM!
Sort Order:  

Hi! I am a robot. I just upvoted you! I found similar content that readers might be interested in:
http://makerwannabe.com/

If anyone reads these comments...

2 more posts left, then I will be adding on Steemit exclusively ;)

No problem in reposting from your own blog. The Cheetah-bot is mainly meant to point out if anybody steals content.

I read up and saw that, I am just a bit concerned that a post a day would lead to a flag being triggered.

I appreciate what is being done through the bot, it would be a pity for Steemit to be overrun with spam.

Until now there has been a limit on 4 posts a day, but that is lifted in the next hardfork in a couple of days. The real concern was that copyrighted material would be taken and posted here as own work. Like if somebody copy-pasted your blog and presented your images and text as their own.

With this you are in no danger of being flagged.

Oh, and a cool modelling-post by the way :)

Thanks!

I got frustrated with the trunk, so it's in a box now, until I have some more patience.